Most water plans fall apart on paper before they ever fail at sea. A crew of four, eighteen days of trade wind sailing, four hundred litres of tankage, and a rough guess at daily consumption. The numbers look fine in the marina. They stop looking fine on day nine, when the tank gauge is lower than the calendar says it should be and the nearest chandlery is a thousand miles behind you.

A watermaker for sailboat use changes that arithmetic completely, but only if you plan around it properly. Buying the unit is the easy part. Sizing it to your crew, budgeting the power it needs from a system that also runs your autopilot and fridge, and building in a fallback for the day it stops producing: that is the work that actually determines whether your water plan holds.

This guide covers the consumption maths, the three places offshore systems fail, how to build redundancy that is worth the locker space, and how to size a system for the passage you might do rather than the one you have planned.

What this guide covers:

  • How much water a sailboat actually uses offshore
  • What happens when production stops mid-passage
  • Building redundancy into your water plan
  • Power budgeting for a sailboat watermaker
  • Which design choices survive an ocean crossing
  • How to size a system for your crew and route

How Much Water Does a Sailboat Actually Use Offshore?

Cruising yachts typically consume somewhere between 4 and 20 litres per person per day, with roughly 6 litres being a common working average for a disciplined crew. That range is the whole problem. The gap between the low end and the high end is a factor of five, and where you land inside it depends less on planning than on habit.

The real number is higher than the plan

Potable water consumption for direct use is the smallest line item. Cooking, washing up, rinsing salt off skin and gear, and the occasional shower are what move the total. Crews who plan for 6 litres and then discover the reality of two weeks without a proper wash tend to drift upward fast. Heat makes it worse. Trade wind passages run warm, and hydration needs climb with sustained exposure.

Build your estimate on the high end of your crew’s likely behaviour, not the number that makes the spreadsheet work. If you plan for 12 litres per person per day and use 8, you have a buffer. If you plan for 6 and use 12, you have a problem that arrives on schedule around the halfway point.

Tankage is a buffer, not a supply

On a passage of more than a week, tankage stops being your water supply and becomes your reserve against production loss. That reframing matters. A 400 litre tank does not represent eighteen days of water for four people. It represents roughly eight days of emergency margin if the system stops on day one, and considerably less if you started the passage with the tank already down.

Treat the tank as insurance. Treat the watermaker as the supply, and top the tank whenever conditions and power allow rather than running production only when the gauge gets low.

What Happens When a Watermaker for Sailboat Use Stops Mid-Passage?

Ocean passages break equipment. In a survey of the 290 yachts sailing the 2016 transatlantic rallies, nearly 60 per cent of the fleet reported some form of breakage, and watermaker malfunctions appeared among the reported failures. That is not an argument against carrying a system. It is an argument for knowing exactly how yours fails. Yachting World

The three common failure points

Almost every offshore watermaker problem traces back to one of three places.

  • Intake and raw water supply. A blocked strainer, an air leak on the suction side, or a seacock fouled by growth starves the feed pump. Symptoms show up as unstable pressure and cavitation noise before production drops.
  • Pre-filtration. Silty anchorages, plankton blooms, and sargassum weed clog pre-filters far faster than clearer offshore water. A clogged filter drops feed pressure and forces the high-pressure pump to work against a restriction it was not designed for.
  • Pressure and control. Anything that regulates or monitors operating pressure is a failure candidate. Electronic controls can require specialized diagnostic equipment compared to straightforward mechanical systems.

The first two are user-serviceable at sea with spares and ten minutes. The third depends entirely on how the system was designed, which is why we build the way we do. Our full argument for that approach is set out in Why offshore watermakers need to be built differently.

Why “we will fix it in port” is not a plan

Coastal cruising forgives equipment failure because the failure window is short. Offshore, a system that cannot be repaired by the person who owns it is functionally the same as a system that is not aboard. The relevant question is not whether a component might fail. It is whether you can identify the fault, reach the part, and replace it with something in your spares kit while the boat is moving.

Building Redundancy Into Your Water Plan

Redundancy for water does not mean a second watermaker. On most cruising sailboats, that is neither practical nor necessary. It means a layered plan where each layer buys you time to fix the layer above it.

Tank capacity, jerry cans and emergency reserve

Work backwards from your worst case. If the system stopped on day one and you had to complete the passage on stored water at a strict ration, would you make landfall? For most crews that means arriving at the start line with tanks full, plus 20 to 40 litres in jerry cans stowed low and secured, plus a small sealed emergency reserve that does not get touched for washing up.

Split tankage is worth having if your boat allows it. A single large tank means one contamination event, one leak or one failed fitting takes everything.

Spares that matter versus spares that sit in a locker

Preparation surveys consistently show that late or untested work causes problems offshore. Reporting on transatlantic preparation found that around a third of surveyed skippers had issues with work already completed before departure, requiring further repairs or modifications. New equipment fitted the week before departure is not proven equipment. Wikipedia

Carry pre-filters in quantity, a spare set of seals and O-rings, the pump service items specified for your model, and a spare high-pressure hose. Skip the exotic components you could not fit at sea anyway. Our guidance on this is set out in spares and consumables worth carrying on a long passage.

Then run the system hard before you leave. Cruising World’s reporting on transatlantic preparation makes the same point that experienced passage makers make repeatedly: learn every system aboard before you go, including the watermaker, rather than reading the manual for the first time at sea.

Power Budgeting for a Sailboat Watermaker

A watermaker is a load, and on a sailboat that load competes with the autopilot, the fridge, navigation instruments, and communications. Getting the power side wrong is one of the most common reasons a well-chosen system ends up underused.

Amp draw against your generation capacity

Start with the daily energy balance rather than the peak draw. If your system pulls 20 amps at 12V and you need it running two hours a day, that is 40 amp-hours. Against a solar array and a hydrogenerator on a downwind passage, that is usually comfortable. Against solar alone under a spinnaker that shades half the panels, it may not be.

The practical answer for many cruisers is to run production during the hours when generation is strongest, rather than treating water making as an evening job that competes with the fridge for battery capacity.

Why DC systems suit sailboats

For sailboats without a generator, 12V and 24V DC watermakers integrate directly into the house bank and avoid the losses and complications of running an inverter or firing up an engine for water alone. Larger vessels with generators or shore-independent AC supply have more freedom. If you are weighing the options across your whole electrical setup, our overview of power options for onboard desalination breaks down the trade-offs.

Which Design Choices Survive an Ocean Crossing?

Two systems can produce identical water in a test tank and behave completely differently three weeks into a passage. The difference is rarely output. It is what happens under vibration, heel, salt exposure, and repeated start-and-stop cycles, and how much of the system a non-specialist can service.

Mechanical simplicity against electronic control

Energy recovery devices and electronic control circuits deliver efficiency gains that matter in some applications. They also add failure modes that require specialist diagnosis. Offshore, where a technician is not an option, a system built around a robust mechanical pump and straightforward pressure control is easier to keep running than one whose faults live in a control board.

That is a deliberate engineering choice rather than a limitation. Across the AML/S series since 1997, ECHOTec systems have accumulated more than 40 million collective operating hours, and 5,000-plus units are working worldwide today. The design decisions behind that record were made by people who assumed the owner would be the one holding the wrench.

Corrosion resistance and serviceability at sea

Salt air finds every weakness. Corrosion-resistant components, sensible material choices at every fitting, and physical layout that lets you reach filters and seals without dismantling half the installation are what separate a system you can maintain offshore from one you can only maintain at a dock. Our marine watermaker range is built around exactly that principle.

How Do You Size a Watermaker for a Sailboat?

Sizing is a function of three things: how many people are aboard, how long you run the system each day, and how much margin you want.

Crew size, passage length, and daily run hours

Take your realistic daily consumption per person, multiply by crew, and add 25 per cent. That is your daily production target. Divide by the number of hours you are comfortable running the system on a typical day, and you have the output rating you need.

A crew of four at 12 litres per person per day needs roughly 48 litres, plus margin, so call it 60 litres. Running two hours a day means a system producing 30 litres per hour. Running one hour a day means 60 litres per hour and a bigger power budget.

Size for the passage you might do

Cruising plans expand. The couple who bought a system for Caribbean island hopping end up crossing the Pacific two seasons later, and the small unit that was adequate for two people at anchor becomes marginal with guests aboard on a long passage.

Buying slightly larger than today’s requirement costs less than replacing a system that turned out to be undersized, and a larger unit run for fewer hours puts less cumulative wear on the pump than a small unit running continuously. If you want help running these numbers against your specific boat and route, that is a conversation worth having before you commit.

Conclusion

A watermaker for sailboat use is not a convenience item on an ocean passage. It is the difference between rationing and living normally, and between a plan that survives a component failure and one that does not. Get the consumption estimate honest, treat tankage as reserve rather than supply, budget the power properly, carry the spares you can actually fit at sea, and choose a system you can service yourself when the nearest technician is a week away.

Curious what size system you would need for your vessel and your intended route? Get in touch at sales@echotecwatermakers.com or visit echotecwatermakers.com to explore our full range and work it out with our team.

Frequently Asked Questions

How much water does a watermaker for a sailboat produce per hour?

Compact DC systems suited to cruising sailboats typically produce in the range of 25 to 60 litres per hour, while larger AC units produce considerably more. The right figure depends on your crew size and how many hours a day you are willing to run the system against your available power.

Can you run a sailboat watermaker while sailing offshore?

Yes, and most cruisers do. Production while underway is normal, though heavy heel or rough conditions can occasionally introduce air at the intake on some installations. Running the system on different points of sail during your shakedown will reveal any such issue before you depend on it.

Is a 12v watermaker for sailboat use powerful enough for a crossing?

For a crew of two to four, a well-sized 12V DC system is generally sufficient. The limiting factor is usually charging capacity rather than the unit itself, so match the system to your solar, wind, or hydrogeneration output rather than to your battery bank size alone.

What is the best watermaker for sailboat cruising?

The one you can service yourself with parts you carry aboard. Output and efficiency matter, but on long passages serviceability and corrosion resistance determine whether the system is still producing water at the end of the trip.

Do I still need water tanks if I have a desalinator for sailboat use?

Yes. Tankage is your reserve against production loss and your buffer for periods when power is short. Plan for enough stored water to complete a meaningful portion of the passage if the system stopped on day one.